# Failed to build image for custom board **URL:** \ **Category:** Support\ **Created:** [October 10, 2021, 1:23pm UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117 "2021-10-10T13:23:18Z")\ **Posts on this page:** 7\ **Page:** 1
**Author:** ![shalom](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.pynq.io/shalom/32/1308_2.png) [@shalom](https://discuss.pynq.io/u/shalom)\ **Post date:** [October 10, 2021, 1:23pm UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117/1 "2021-10-10T13:23:18Z")
Hello Iam trying to build pynq2.6 for zcu102 I have installed petalinux / vivado / and vitis 2020.1 then running the cmd : make BOARDS=ZCU102 I get the following error: version | fgrep 4.0.0 /bin/bash: version: command not found Makefile:339: recipe for target ‘qemu\_check\_aarch64’ failed make: [qemu\_check\_aarch64] Error 1 (ignored) vivado -version | fgrep 2020.1 Vivado v2020.1 (64-bit) vitis -version | fgrep 2020.1 \*\*\*\*\*\* Vitis v2020.1 (64-bit) which petalinux-config /home/shal/petalinux/2020.1/tools/common/petalinux/bin/petalinux-config which arm-linux-gnueabihf-gcc /home/shal/Xilinx/Vitis/2020.1/gnu/aarch32/lin/gcc-arm-linux-gnueabi/bin/arm-linux-gnueabihf-gcc which microblaze-xilinx-elf-gcc /home/shal/petalinux/2020.1/tools/xsct/gnu/microblaze/lin/bin/microblaze-xilinx-elf-gcc which ct-ng Makefile:356: recipe for target ‘checkenv’ failed make: \*\*\* [checkenv] Error 1 I dont understand what the issue Thank you very much Shal ---
**Author:** ![abdyoyo](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.pynq.io/abdyoyo/32/2297_2.png) [@abdyoyo](https://discuss.pynq.io/u/abdyoyo)\ **Post date:** [October 11, 2021, 4:50am UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117/2 "2021-10-11T04:50:40Z")
Please write the code part of the post inside the code blockquote (Ctrl+Shift+9 to use it here). Have you seen the documentation on the meta-pynq and image building for pynq? If not, reading that and figuring out will solve your issue. Abhijeet ---
**Author:** ![shalom](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.pynq.io/shalom/32/1308_2.png) [@shalom](https://discuss.pynq.io/u/shalom)\ **Post date:** [October 12, 2021, 8:12am UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117/3 "2021-10-12T08:12:40Z")
Ok thank you will check that ---
**Author:** ![ATchelet](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.pynq.io/atchelet/32/2439_2.png) [@ATchelet](https://discuss.pynq.io/u/ATchelet)\ **Post date:** [October 12, 2021, 11:47am UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117/4 "2021-10-12T11:47:03Z")
I think I might have had this error after not specifying the architecture in the \*.spec file. It’s not written in the how-to guide, but I saw it on the \*.spec file of the prebuilt boards. For the ZCU102, which has the AArch64 CPU, you need to add this line to your \*.spec file. I assume you replaced MyBoard from the guide with ZCU102: > ARCH\_ZCU102 := aarch64 Hope it works for you ---
**Author:** ![shalom](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.pynq.io/shalom/32/1308_2.png) [@shalom](https://discuss.pynq.io/u/shalom)\ **Post date:** [October 12, 2021, 12:54pm UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117/5 "2021-10-12T12:54:44Z")
Hi Yes set the correct arch for the board : here is my .spec file ARCH\_ZCU102 := aarch64 BSP\_ZCU102 := xilinx-zcu102-v2020.1-final.bsp FPGA\_MANAGER\_ZCU102 := 1 STAGE4\_PACKAGES\_ZCU102 := ethernet I currently check , maybe some linux packages have not been correctly installed Thanks Shal ---
**Author:** ![shalom](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.pynq.io/shalom/32/1308_2.png) [@shalom](https://discuss.pynq.io/u/shalom)\ **Post date:** [October 14, 2021, 7:10am UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117/6 "2021-10-14T07:10:41Z")
Hello So i recheck all my setup , reinstall packages that petalinux need and I successfully generate an image for petalinux for zcu102 when I go though the pynq procedure , I run the **./scripts/setup\_host.sh** and get the following error : **The following packages have unmet dependencies: libglib2.0-dev : Depends: libglib2.0-0 (= 2.56.1-2ubuntu1) but 2.56.4-0ubuntu0.18.04.4 is to be installed Depends: libglib2.0-bin (= 2.56.1-2ubuntu1) libsdl1.2-dev : Depends: libasound2-dev but it is not going to be installed Depends: libcaca-dev but it is not going to be installed Depends: libglu1-mesa-dev but it is not going to be installed or libglu-dev Depends: libpulse-dev but it is not going to be installed Depends: libx11-dev but it is not going to be installed Depends: libxext-dev but it is not going to be installed libssl-dev : Depends: libssl1.1 (= 1.1.0g-2ubuntu4) but 1.1.1-1ubuntu2.1~18.04.5 is to be installed Recommends: libssl-doc but it is not going to be installed E: Unable to correct problems, you have held broken packages.** Is there any script that arrange all those dependencies automatically as petalinux do ? Thanks Shal ---
**Author:** ![shalom](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.pynq.io/shalom/32/1308_2.png) [@shalom](https://discuss.pynq.io/u/shalom)\ **Post date:** [October 19, 2021, 8:03pm UTC](https://discuss.pynq.io/t/failed-to-build-image-for-custom-board/3117/7 "2021-10-19T20:03:19Z")
I delete the VMs and recreate a new one bionic 18.04.6 instead of 18.04.4 So the **./scripts/setup\_host.sh** passed successfully Now going to next steps… Thanks Shal