Hello, Do I need to change/set the UART used for serial console in petalinux config when using the bsp with petalinux built from here PYNQ/boards/Pynq-Z2/petalinux_bsp at master · Xilinx/PYNQ · GitHub if I do what are the settings exactly ? Also what should be the partition/file structure for the …

Ok this is frustrating, I can not get the SD to boot…I assume I need that green Done LED on the board to show ? Nor can I probably as a result of the above serial connect to the UART at all ? , Putty just beeps at me when I try to connect to COM4 which is where the UART seems to be ? There seems to…

The green “done” is the bitstream being loaded to the FPGA. This happens after the system boots in the standard Z2 boot image. This step is not essential. What are you trying to do (why are you building a custom image), and why do you think you would need to change the UART settings? Can you outli…

I am simply trying to build the basic image to see if I can indeed do that with no issues. It turns out the UART settings appear to be correct by default. Or are they ? (default is UART 0) I think my issue may be in the setup of the SD card ? I have put the files on the SD card, BOOT.bin, image.u…

At this point I suspect BOOT.BIN is simply not getting loaded at all for some reason ? (though the Pynq 2.5 SD image loads fine) The UART setting in petalinux-configure and/or the bsp package itself also maybe somehow wrong or mismatched would seem like an unlikely but alternative guess ? Also per…

This is a very odd use case. I think you may have missed some recipes from meta-pynq layer . We never tested the bsp outside of the SD build flow. I don’t know where you got stuck- is any message showing on terminal, or nothing? I don’t think your board is broken since you have PYNQ 2.5 image runni…

Ok another update. I managed to get a Vitis standalone project working on the board . I imported the Z2 bsp already mentioned in this thread into Vivado, exported to a xsa+bitstream then used that xsa to make a new platform In Vitis and then made the example “hello world” project for that platform …

For the raw bsp constructed, we put a meta-user layer on top of it. It has all the recipes you can see in PYNQ/boards/Pynq-Z2/petalinux_bsp/meta-user/recipes-bsp at master · Xilinx/PYNQ · GitHub , then we put a meta-pynq layer on top: PYNQ/sdbuild/boot/meta-pynq at master · Xilinx/PYNQ · GitHub . For…

Ok, how exactly do I apply the bsp recipes specifically ? i.e these PYNQ/boards/Pynq-Z2/petalinux_bsp/meta-user/recipes-bsp at master · Xilinx/PYNQ master/boards/Pynq-Z2/petalinux_bsp/meta-user/recipes-bsp Python Productivity for ZYNQ. Contribute to Xilinx/PYNQ development by creating…

Keep getting an error when trying to add the bsp recipes: Following this: https://www.zachpfeffer.com/single-post/Add-a-Yocto-Layer-to-a-PetaLinux-Project-and-Build-a-Recipe-in-the-Layer-with-PetaLinux-Tools Putting the contents of: PYNQ/boards/Pynq-Z2/petalinux_bsp/meta-user at master · X…

Blank post to bump this to make replys work.

Pynq Z2 Petalinux boot and serial?

Support

mfny March 22, 2020, 12:07pm 19

A reply to bump this.

Topic		Replies	Views
PYNQ sd card for custom board fails to boot Support	12	3095	June 7, 2019
Porting of petalinux meta-user recipes Support	8	3104	July 27, 2022
Pynq 2.6 custom board image build method that works Learn	4	6709	January 21, 2022
How can i get pynq-z2.bsp? Support	2	1831	September 10, 2020
PYNQ-2.4 for Zedboard v2018.3 Support	6	4279	May 28, 2023

Pynq Z2 Petalinux boot and serial?

Related topics