Hello there,
I followed the tutorial from PYNQ-Z2 Setup Guide — Python productivity for Zynq (Pynq)
and I checked with 2 SD cards.
I see only one CR8 red LED - there is no blue, yellow or green LED’s.
How I can check if the board that I bought is damaged?
This is the log from boot:
Device: mmc@e0100000
Manufacturer ID: 1b
OEM: 534d
Name: 00000
Bus Speed: 50000000
Mode : SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 58.6 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
4771268 bytes read in 275 ms (16.5 MiB/s)
Loading kernel from FIT Image at 10000000 …
Using ‘conf@1’ configuration
Verifying Hash Integrity … OK
Trying ‘kernel@0’ kernel subimage
Description: Linux Kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x100000d4
Data Size: 4752880 Bytes = 4.5 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00080000
Entry Point: 0x00080000
Hash algo: sha1
Hash value: f0d022f59e1266bfc5bb33d36a03c8f9d3210c1f
Verifying Hash Integrity … sha1+ OK
Loading fdt from FIT Image at 10000000 …
Using ‘conf@1’ configuration
Verifying Hash Integrity … OK
Trying ‘fdt@0’ fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x104887b8
Data Size: 17093 Bytes = 16.7 KiB
Architecture: ARM
Hash algo: sha1
Hash value: 8899d6d25301f1e831133eac3ff0fc67091de697
Verifying Hash Integrity … sha1+ OK
Booting using the fdt blob at 0x104887b8
Loading Kernel Image … OK
Loading Device Tree to 07ff8000, end 07fff2c4 … OK
Starting kernel …
Booting Linux on physical CPU 0x0
Linux version 4.19.0-xilinx-v2019.1 (oe-user@oe-host) (gcc version 8.2.0 (GCC)) #1 SMP PREEMPT Thu Oct 3 17:13:49 UTC 2019
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: xlnx,zynq-7000
bootconsole [earlycon0] enabled
Memory policy: Data cache writealloc
cma: Reserved 128 MiB at 0x18000000
random: get_random_bytes called from start_kernel+0x80/0x3e4 with crng_init=0
percpu: Embedded 16 pages/cpu @(ptrval) s35980 r8192 d21364 u65536
Built 1 zonelists, mobility grouping on. Total pages: 129920
Kernel command line: root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait devtmpfs.mount=1 uio_pdrv_genirq.of_id=“generic-uio” clk_ignore_unused
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 376512K/524288K available (7168K kernel code, 230K rwdata, 1800K rodata, 1024K init, 258K bss, 16704K reserved, 131072K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0x(ptrval) - 0x(ptrval) (8160 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 230 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 259 kB)
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
Tasks RCU enabled.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
efuse mapped to (ptrval)
slcr mapped to (ptrval)
L2C: platform modifies aux control register: 0x72360000 → 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 → 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at (ptrval)
Zynq clock init
sched_clock: 64 bits at 325MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4af477f6aa , max_idle_ns: 440795207830 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 5513 18127 ns
timer #0 at (ptrval), irq=17
Console: colour dummy device 80x30
console [tty0] enabled
bootconsole [earlycon0] disabled
Booting Linux on physical CPU 0x0
Linux version 4.19.0-xilinx-v2019.1 (oe-user@oe-host) (gcc version 8.2.0 (GCC)) #1 SMP PREEMPT Thu Oct 3 17:13:49 UTC 2019
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: xlnx,zynq-7000
bootconsole [earlycon0] enabled
Memory policy: Data cache writealloc
cma: Reserved 128 MiB at 0x18000000
random: get_random_bytes called from start_kernel+0x80/0x3e4 with crng_init=0
percpu: Embedded 16 pages/cpu @(ptrval) s35980 r8192 d21364 u65536
Built 1 zonelists, mobility grouping on. Total pages: 129920
Kernel command line: root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait devtmpfs.mount=1 uio_pdrv_genirq.of_id=“generic-uio” clk_ignore_unused
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 376512K/524288K available (7168K kernel code, 230K rwdata, 1800K rodata, 1024K init, 258K bss, 16704K reserved, 131072K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0x(ptrval) - 0x(ptrval) (8160 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 230 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 259 kB)
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
Tasks RCU enabled.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
efuse mapped to (ptrval)
slcr mapped to (ptrval)
L2C: platform modifies aux control register: 0x72360000 → 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 → 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at (ptrval)
Zynq clock init
sched_clock: 64 bits at 325MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4af477f6aa , max_idle_ns: 440795207830 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 5513 18127 ns
timer #0 at (ptrval), irq=17
Console: colour dummy device 80x30
console [tty0] enabled
bootconsole [earlycon0] disabled
Calibrating delay loop (skipped), value calculated using timer frequency… 650.0 0 BogoMIPS (lpj=3250000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: Spectre v2: using BPIALL workaround
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100060
rcu: Hierarchical SRCU implementation.
smp: Bringing up secondary CPUs …
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU1: Spectre v2: using BPIALL workaround
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (1300.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911 2604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x(ptrval)
zynq-pinctrl 700.pinctrl: zynq pinctrl initialized
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 27, base_baud = 6250000) is a xuartps
console [ttyPS0] enabled
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
videodev: Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@l inux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
FPGA manager framework
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing.
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
Initialise system trusted keyrings
workingset: timestamp_bits=14 max_order=17 bucket_order=3
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
Key type asymmetric registered
Asymmetric key parser ‘x509’ registered
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
io scheduler mq-deadline registered
io scheduler kyber registered
dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Even ts-16
brd: module loaded
loop: module loaded
m25p80 spi0.0: found s25fl128s, expected n25q512a
m25p80 spi0.0: s25fl128s (16384 Kbytes)
4 fixed-partitions partitions found on MTD device spi0.0
Creating 4 MTD partitions on “spi0.0”:
0x000000000000-0x000000500000 : “boot”
0x000000500000-0x000000520000 : “bootenv”
0x000000520000-0x000000fa0000 : “kernel”
0x000000fa0000-0x000001000000 : “spare”
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
CAN device driver interface
libphy: MACB_mii_bus: probed
RTL8211E Gigabit Ethernet e000b000.ethernet-ffffffff:01: attached PHY driver [RT L8211E Gigabit Ethernet] (mii_bus:phy_addr=e000b000.ethernet-ffffffff:01, irq=PO LL)
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 29 (00 :05:6b:01:00:5b)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver usb_serial_simple
usbserial: USB Serial support registered for carelink
usbserial: USB Serial support registered for zio
usbserial: USB Serial support registered for funsoft
usbserial: USB Serial support registered for flashloader
usbserial: USB Serial support registered for google
usbserial: USB Serial support registered for libtransistor
usbserial: USB Serial support registered for vivopay
usbserial: USB Serial support registered for moto_modem
usbserial: USB Serial support registered for motorola_tetra
usbserial: USB Serial support registered for novatel_gps
usbserial: USB Serial support registered for hp4x
usbserial: USB Serial support registered for suunto
usbserial: USB Serial support registered for siemens_mpi
chipidea-usb2 e0002000.usb: e0002000.usb supply vbus not found, using dummy regulator
chipidea-usb2 e0002000.usb: Linked as a consumer to regulator.0
ULPI transceiver vendor/product ID 0x0451/0x1507
Found TI TUSB1210 ULPI transceiver.
ULPI integrity check: passed.
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
i2c /dev entries driver
cdns-i2c e0004000.i2c: 100 kHz mmio e0004000 irq 23
cdns-i2c e0005000.i2c: 100 kHz mmio e0005000 irq 24
cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at (ptrval) with timeout 10s
EDAC MC: ECC not enabled
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
xlnk xlnk: Major 244
xlnk xlnk: xlnk driver loaded
xlnk xlnk: xlnk_pdev is not null
fpga_manager fpga0: Xilinx Zynq FPGA Manager registered
NET: Registered protocol family 10
Segment Routing with IPv6
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20170425 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20170425)
can: broadcast manager protocol (rev 20170425 t)
can: netlink gateway (rev 20170425) max_hops=1
Registering SWP/SWPB emulation handler
Loading compiled-in X.509 certificates
mmc0: new high speed SDXC card at address 0001
of-fpga-region fpga-full: FPGA Region probed
mmcblk0: mmc0:0001 00000 58.6 GiB
hctosys: unable to open rtc device (rtc0)
of_cfs_init
of_cfs_init: OK
cfg80211: Loading compiled-in X.509 certificates for regulatory database
mmcblk0: p1 p2
cfg80211: Loaded X.509 cert ‘sforshee: 00b28ddf47aef9cea7’
platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
clk: Not disabling unused clocks
cfg80211: failed to load regulatory.db
ALSA device list:
No soundcards found.
random: fast init done
EXT4-fs (mmcblk0p2): recovery complete
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 1024K
Run /sbin/init as init process
systemd[1]: System time before build time, advancing clock.
systemd[1]: Failed to insert module ‘autofs4’: No such file or directory
systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
systemd[1]: Detected architecture arm.
Welcome to PynqLinux, based on Ubuntu 18.04!
systemd[1]: Set hostname to .
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Reached target System Time Synchronized.
[ OK ] Reached target System Time Synchronized.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
systemd[1]: Started ntp-systemd-netif.path.
[ OK ] Started ntp-systemd-netif.path.
systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on Journal Socket.
Starting Load Kernel Modules…
Starting Create Static Device Nodes in /dev…
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on udev Kernel Socket.
Starting udev Coldplug all Devices…
[ OK ] Listening on Syslog Socket.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Reached target Slices.
Starting Nameserver information manager…
Starting Restore / save the current clock…
Mounting POSIX Message Queue File System…
[ OK ] Reached target Remote File Systems.
Starting Remount Root and Kernel File Systems…
[ OK ] Listening on Journal Socket (/dev/log).
Starting Journal Service…
Mounting Kernel Debug File System…
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Reached target Local Encrypted Volumes.
[ OK ] Started Journal Service.
[ OK ] Started Load Kernel Modules.
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Started Restore / save the current clock.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Started Nameserver information manager.
[ OK ] Reached target Network (Pre).
Activating swap /var/swap…
Starting Load/Save Random Seed…
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting Enable support for additional executable binary formats…
Starting udev Kernel Device Manager…
Starting Apply Kernel Variables…
Mounting Kernel Configuration File System…
Starting Flush Journal to Persistent Storage…
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Load/Save Random Seed.
[ OK ] Activated swap /var/swap.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Enable support for additional executable binary formats.
[ OK ] Started Apply Kernel Variables.
[ OK ] Mounted Kernel Configuration File System.
Starting Raise network interfaces…
[ OK ] Reached target Swap.
[ OK ] Found device /dev/ttyPS0.
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories…
[ OK ] Started Create Volatile Files and Directories.
[ OK ] Started ifup for eth0.
Starting Network Time Synchronization…
Starting Network Name Resolution…
[ OK ] Started Entropy daemon using the HAVEGE algorithm.
Starting Update UTMP about System Boot/Shutdown…
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Initialization.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Message of the Day.
[ OK ] Started resolvconf-pull-resolved.path.
[ OK ] Reached target Paths.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Reached target Timers.
[ OK ] Listening on UUID daemon activation socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Jupyter Notebook Server…
Starting System Logging Service…
Starting Login Service…
Starting LSB: automatic crash report generation…
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started Login Service.
[ OK ] Started ntp-systemd-netif.service.
[ OK ] Started Regular background program processing daemon.
[ OK ] Started Set the CPU Frequency Scaling governor.
Starting LSB: Load kernel modules needed to enable cpufreq scaling…
Starting Dispatcher daemon for systemd-networkd…
Starting resolvconf-pull-resolved.service…
Starting WPA supplicant…
Starting Resize Filesystem on SD card…
Starting PYNQ PL Server…
[ OK ] Started Network Name Resolution.
[ OK ] Started System Logging Service.
[ OK ] Started Resize Filesystem on SD card.
[ OK ] Started PYNQ PL Server.
[ OK ] Started resolvconf-pull-resolved.service.
[ OK ] Started WPA supplicant.
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Started LSB: automatic crash report generation.
[ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
Starting LSB: set CPUFreq kernel parameters…
[ OK ] Started LSB: set CPUFreq kernel parameters.
[ OK ] Started Dispatcher daemon for systemd-networkd.
Stopping Network Name Resolution…
[ OK ] Stopped Network Name Resolution.
Starting Network Name Resolution…
Starting resolvconf-pull-resolved.service…
[ OK ] Started Network Name Resolution.
[ OK ] Started resolvconf-pull-resolved.service.
[ OK ] Started Raise network interfaces.
[ OK ] Reached target Network.
Starting Permit User Sessions…
[ OK ] Started Unattended Upgrades Shutdown.
Starting OpenBSD Secure Shell server…
[ OK ] Reached target Network is Online.
[ OK ] Started ISC DHCP IPv4 server.
Starting Samba NMB Daemon…
[ OK ] Started ISC DHCP IPv6 server.
[ OK ] Started Permit User Sessions.
[ OK ] Started Serial Getty on ttyPS0.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
PYNQ Linux, based on Ubuntu 18.04 pynq ttyPS0
pynq login: xilinx (automatic login)
Last login: Fri Jul 17 21:31:59 UTC 2020 on ttyPS0
Welcome to PYNQ Linux, based on Ubuntu 18.04 (GNU/Linux 4.19.0-xilinx-v2019.1 armv7l)
To run a command as administrator (user “root”), use “sudo ”.
See “man sudo_root” for details.
xilinx@pynq:~$
it seems that both the PL server and the jupyterhub server is started just fine and linux boots. can you connect to jupyter? which pynq version are you using?
Thanks for asking @FrankB
I were unable to connect to Jupiternotebook.
The problem was with
systemd[1]: Failed to insert module ‘autofs4’:
It was caused by a partitioning problem. I was using Rufus to burn the image, and I should use Win32 Disk Imager.
After burning with Win32 Disk Imager I see colourfull LED’s.
1 Like